Nautor's Swan Swan 115-03

6,774,375 GBP (7,950,000 EUR)

Mediterranean Yacht Management sarl

Email the seller

Description

Highland Fling 15 is Germán Frers design along with the demanding requirements of a highly experienced, serial Swan yacht owner. Built to the highest standards of performance. She has a minimalist interior and flush deck. With a full carbon hull and deck.
Highland Fling 15 is a proven cruiser / racer; 1st Americas Cup SYC 2017, 3rd Palma SYC 2018, 3rd Rolex Maxi 2016
HULL & APPENDAGES
Construction
The layup is of a foam cored carbon fibre epoxy reinforced construction in a female mold.
The hull is pre-preg carbon fibre foam sandwich. The laminate is vacume consolidated and oven cured at + 70C. The core is M-Grade Corecell SAN Foam with high density used in the high loaded areas.
A high proportion of the fibres are unidirectional resulting in a stiff structure
The stiffeners and structural bulkheads are made using Carbon SE70 Pre-preg and Nomex, vacuum consolidated at +70C. Special care is taken to assure rigid foundations and adhesion to the hull.
Additional carbon reinforcement is applied around areas where there are openings and cut outs.
Keel
Lifting keel optimization:
- Stroke 4.5 m - 6.75 (standard is 4.5 m - 6.5 m)
- Keel trunk laminate and core optimization
- Chord length 1.738 m (standard is 2.073 m)
- Weldox 900 material (standard is Weldox 700)
- Titanium bottom plate and tapping bars (standard is
stainless steel)
- Titanium bearings and side wedges (standard is
stainless steel).
Light weight lifting keel cylinder instead of standard.
Custom 23,3t bulb
Steering Systems
The steering system is a twin rudder and twin wheel sprocket with chain and cables.
The rudders are custom design by Owen Clark, Isotop supplied, carbon fibre, foam core, epoxy construction with custom tubular carbon fibre stocks and sacrificial tips. JP3 rudder bearings are supplied.
Custom performance steering system with weather
rudder float system and composite quadrants instead of
standard.
DECK
The main deck is of carbon fibre pre-preg sandwich construction with Nomex Honeycomb Core. The coach roof and coamings are of a carbon fibre pre-preg sandwich construction with Corecell Core. High density core is used in the high load areas and in way of deck fittings. The deck is bonded to the hull using high strength structural adhesives.
The teak deck consists of teak battens 65 x 6mm with grey 5mm caulking. The teak decking is vacuum bonded with epoxy adhesive.
Deck Equipment
All winches are hydraulically driven by CCHE Hydraulics
Winches
Two Harken B1235.3 STR AAA HY primary cockpit winches with base sheave
Three Harken.3 STR AAA HY cockpit halyard winches
Two Harken B1235.3 STR AAA HY main sheet winches reduced
Two Harken B1235.3 STR AAA HY running backstay winches
One Harken B1125.3 STR AAA HY utility winch
One anchor windlass
Sail Handling Systems
There are Harken hard anodized aluminum tracks for two jib cars and harken mainsheet traveler with custom cars and stoppers.
Spinlock ZS jammers for halyards, preventer, tack and reef lines
Reckmann UD5 furling headstay with Carbo-link torsional headstay
Eight pad eyes on bulwark
Pushpit and Pulpit
The pushpit and pulpit and lifelines are with spacing and in occordence with ISAF/ORG requirements
32mm polished stainless tube. The pushpit has an access gate for the gangway.
Lifelines and Stanchions
The Stanchions are 610mm high with 2 wire lifelines of 5mm and 4mm, spacing and in occordence with ISAF/ORG requirements.
Cleats and Fairleads
Six custom titanium pop-up cleats and 4 custom titanium fairleads
Other
Custom titanium toe rails forward of mast
One custom carbon fibre mast collar
One flag pole socket
Two custom carbon fibre railing between steering pedestals, by aft deck hatch
Hatches and Windows
Teak covered Deck Hatchs
One 600 x 600mm Anchor and windlass hatch
One 1600 x 1600mm sliding hatch to forward sail storage
One 1200 x 1200mm aft lazzarette hatch
Two large dingy well hatchs
Main Companionway
The main entrance has a manually operated forward sliding hatch with a drop board for closure, with removable canvas spray hood
Crew Entrance
One raised forward sliding hatch just forward of the steering pedestals, with removable spray hood
Cockpits Seats and Tables
Two removable seats either side of the cockpit, with cushions
Dingy Well
One 4m long x 2.4m wide x 0.7/0.9m deep dingy well with teak covered carbon hatch doors. Large well drains installed. Sea cover provided.
Other
Under deck system for two assymetric tack linetensioners including chain plates, Equiplite 4 ton
Autolocks and hydraulic rams.
Tack slider in stainless steel. Deck flange is similar Reckman UD5-SC furler / headstay tensioner
Fixed custom carbon fibre bowsprit
Installation of customer supplied lash tangs on bulwark.
Two lash tangs on stern bulwark
Equiplite Code-0 tack line lock upgraded from 4t to 6,5t.
Spinnaker sheet lead under deck through sheave boxangled 20° outboard in bulwark
Load pins on backstays
Removable painted carbon fibre radar post on aft deck with aluminium platform for scanner and three antennas.
INTERIOR

General
The interior is open plan minimilist design using white vinyl pannels in the head liners and hand rubbed satin varnish white oak veneers and hardwood to create a bright lively atmosphere. All furniture the joinery are built with best yacht practice and wood selection is in accordence and first grade materials.
Master Cabin (Fwd)
The master Cabin has been left for the new owner to choose a custom arrangement, or leave it as is. Presently the configuration of Highland Fling 15, as a performance cruiser the owner prefered to have the forward part of the interior as sail storage
Heads
There are six heads on board, pne per cabin. Tecma carbon fibre toilets throughout. Carbon fibre painted countertops with perspex mirrors, acrylic shower doors with custom carbon fibre foam floorboards.
Galley
Galley work tops in painted carbon fiber sandwich
Built in cupboard storage, above counter, painted white
Built in cupboard storage, below counter, white oak veneer with satin varnish finish
Double sink in clear carbon fiber.
One microwave oven Miele M 8261-2171, 2.17 kW, 800W
One dishwasher Miele G5985 scvI XXL, 230VAC, 202kW
One refrigerator Frigonautic 24VDC 600liter
One freezer Frigonautic 24VDC, 370liter
One electric oven Miele H 6090 B, 230VAC 3.7kW 900mm wide
One induction hob 5 cooking zones Miele KM 6387, 400VAC 11.1kW
Forward VIP Cabins
There are two cabins located either side of he mast, with double size berth, outboard. The cabins are finished with satin varnished, white oak veneer panels and doors with white vinyl overheard with removable panels. Ensuite heads.
Aft VIP Cabin
There is one VIP cabin located on the port side, athwart the main companionway entrance. The cabin is finished with satin varnished, white oak veneer panels and door with white vinyl removable overheard panels. Ensuite heads.
Nav Station
The Navigation station is on centerline in the crew quarters with direct access to deck. The station consists of a chart table, instrument panels and a forward-facing floor-mounted swiveling chair.
ENGINE & SYSTEMS
Propulsion System
Type: Retractible Drive System, including the main engine Marine Diesel Sweden 400 VGT. Tuff Torque gear box TTM61A (2.43:1) 4 blade fixed pitch propeller
Thrusters
OYS H-300-V Custom Vertical tube bow thruster
Titanium vertical tube and a carbon tunnel
Plumbing Systems
Pressurized hot and cold water throughout. The pressure water system is multi layered press fitting system. Hot water tubing is insulated. With integrated water tanks, with baffels, inspection covers and vent lines. Side deck filling of from the desalination system. Two x 750 liter fresh water tanks
Deslination System
Recovery Aqua Whisper Mini with a capacity of 118 l/h.
Drainage System
The bilge is divided into 4 sections, forepeak, sail storage, accommodation area, engine room and lazarette. The bilge areas are equipped with a drainage pipe connected to the main bilge pump as well each bilge section is fitted with an automatic 24vdc drain pump to keep them dry.
Two grey water tanks collect all drain water from the washer and dryer, sinks and showers, refrigerator and freezer and air conditioning drip trays.
ELECTRICAL SYSTEM
General
The electrical system is made up of 230VAC, 400 V @ 50Hz and 24 VDC Power supplied by a single-phase Panda diesel generator 18 Kw or shore power. 24VDC power is supplied by a single battery bank 720 Ah. PLC controlled power shedding system, single bus. There are also a number of 230VAC/50Hz appliances fed through DC / AC inverters.
DC System
The yacht has a 2-pole 24V insulated return DC system. The batteries are Mastervolt MLII Ultra 24/5000 lithium ion 24V/180Ah. The on board 24VDC system is made up of a single bank of four batteries with 720Ah capacity. There are also a number of 230VAC/50Hz appliances fed through 24VDC inverters
AC System
The yacht is supplied with AC power fed through a diesel generator or shore power. The diesel generator is a Panda 45PMS 18Kw 50Hz single phase, variable speed. The shore power inlet connector is 230/400V, 5 pole, 63 Amps
Chargers/Inverters
There are two Mass Combi Ultra charger/inverter24/3500-100 with 3 step 100 Amp charging charastics, for charging batteries
The inverters are Master volt Mass Combi Ultra charger/inverter converting 24VDC to single phase 230VAC, 50Hz
One 24VDC/140Amp Bosch alternator on the main engine to charge service batteries
ELECTRONIC SYSTEMS
Navigation Instruments
B&G Zeus Navigation System marine processor
B&G ZM 19T / ZC1 19” touch screen controller at navigation station
B&G ZG 100 GPS antenna
Broadband 4G radar antenna
Class B AIS transponder
Simrad NAIS-400 including GPS and VHF antenna splitter
Gyro Compass Sperry Marine Navigat X Mk2
Sailing Instruments
B&G H 5000 40/40 Displays
Six B&G GFDs
Communications Systems
704 Handheld DSC VHF radio, Simrad HH36 integrating GPS
B&G V90 VHF with wireless VHF handset in cockpit
Yachtspot internet 4G+WiFI system
Yachtspot WiFI terminal
Globesurfer GSM/3G terminal.
Panasonic DECT wireless telephone
Livewire FB 10 PRO
KVH Mini VSAT Satellite telephone terminal
Entertainment Systems
Denon CEOL Piccolo network receiver with two pair of B&W CCM 362 ceiling speakers. Connects through Airplay to any iPod/iPhone/iPad. The systems are installed throughout VIP cabins and crew mess.
Video Systems
One 22” LED TV Samsung Series 4 connects to Samsung Blu-ray player DB-D6500 Located in the crew mess.
MAST & RIGGING
General
The mast and boom are custom high modulus, uni directional, pre-preg carbon fibre, supplied by Hall Spars
SRC Carbon rigging
Carbo link furing headstay
Reckman Furler UD5-SCLW
Sailplan as follows:
1) P=45000 (Plus 1,5M)
2) E=13750
3) ISP=48200
Equipment
B&G H 5000 Auto Pilot Controller
One 150Kg riding anchor
one Fortress FX-125 second anchor
One removable anchor roller for Fortress anchor
120m 14mm galvanized high tensile chain for primary anchor
20m 12mm galvanized high tensile chain for Fortress anchor
125m 25mm plaited nylonanchor rope
Four mooring Lines 20m 20mm
Four mooring lines 40m 20mm
Eight inflatable fenders with custom covers
Anchor light with cable and plugs
Two boat hooks
Safety Equipment
One foghorn Marco EW 3 24VDC
EPIRB McMurdo G-5-M with built in GPS
MOB button installed at each helm station
Hydraulic system emergency stop installed at each helm station and pit
SART McMurdo S4 rescue SART
Two Life Rafts Type: Sea-Safe Pro-Light 12 Man Solas B
SAILS
Race Sails:
North 2016/2017
Main 3DI Raw
J1, J2, 3DI RAW
J3, J4 3DI RAW Furling
Spin staysail KZ Furling on cable
A0, A3, KZ furling on cables
A2, A4
GS/storm jib
Trysail
Doyle 2016/2017
A2, A4
Delivery sails 2016
Main; hounds hoist with two reef
Staysail. KZ Furling on cable
J3 furling on headstay
Price may be changed without notice
Boat is offered subject to still being available
The particulars are believed to be correct but not guaranteed

Seller information

Mediterranean Yacht Management sarl
Mr Giorgio Passarella
Le Beau Rivage
9, avenue d'Ostende
98000
Monaco

General Information

  • Price

    6,774,375 GBP (7,950,000 EUR)

  • Tax

    Paid / Included

  • ID

    1739020

  • length

    35.11m

  • Year

    2016

  • location

    Palma de Mallorca

  • Status

    Available

  • Designer

    Germán Frers

  • New/Used

    Used

  • Beam

    8.12m

  • Draft

    6.75m

  • Displacement

    76000kg

  • Hull

    Carbon SPRINT Pre-preg sandwich hull and deck

  • Keel

    Lifting keel

Propulsion

  • Fuel type

    diesel

  • Fuel capacity

    2000

  • Engine

    Sweden Marine Diesel VGT 400 50 HP @ 3500 RPM

Accommodation

  • Number of cabins

    6

  • Drinking water capacity

    1500L

Boats from this seller

Nautor Swan 68
EUR 1,300,000
Spain
Nautor's Swan 77-006
EUR 740,000
Greece
Nautor Swan 41-025
EUR 105,000
Italy

You may also be interested in...

Nautor's Swan 60-010
EUR 900,000
Spain
Nautor's Swan 68 - 014
EUR 975,000
Spain
NAUTOR'S SWAN Nautor Swan 411
USD 89,000
United States